Capture MRec

This post is also available on: German

1. Manual recording of milk quantities

  1. Open capture > MRec > capture MRec and select the BU to be checked
  1. To start capture, click Start
  1. Add the collected amounts of milk to the animals, the cursor flashes in the column Milk 1, first row

If an animal has fallen exceptionally sharply with the milk yield at the time of the MRec, a cause can be assigned in the column YRC. This also applies to capture of the quantity of milk from a coupling.

In the calculation of the leisPTngsdata, a corrected value for the animal is determined in the VIT, resulting from the milk quantity of the previous MRec and the MRec, which follows thePTtest.

This value is then used in the calculation of the lactation yields.

Assignment of an YRC

  1. Open registration > detection MRec
  2. Click Start to open the capture, if the cursor is in the capture field, an YRC can be assigned
  3. To activate the drop-down list YRC, press
  1. Open drop-down list YRC
  1. Select the YRC relevant to the animal by clicking
  1. To capture another YRC, continue as in 4.
  1. After entering all quantities of milk, click on completeness
Setting for checking completeness
  1. bei Melkfrequenz gesetzt
    • when the check mark is set, the completeness of the values is also checked for groups that have been assigned a higher milking frequency
    • Setting is important when the milk quantities are read in from a technology coupling
  1. bei Melkfrequenz nicht gesetzt
    • additional gems must be marked manually with
    • Setting is important when milk quantities are recorded manually
  1. Confirm the Check completeness window with OK, it is checked whether each animal has at least the number of milk quantities that are stored in the settings Operating data > > BU> Groupin the column Milking Frequency .
  1. Confirm the message registration MRec is incomplete with OK
  1. Complement the missing milk quantities
    • Animals with missing milk quantities are summarized in a list
  1. If all milk quantities are recorded, either continue with 4th, or click Exit MRec
    • finally, a completeness check is carried out again
  1. Confirm the completeness with OK
    • the completed MRec is now on startpage in messages window and can be sent

2. Import of milk quantities from a technical coupling

  1. Open capture animal > MRec > capture MRec
  1. To start capture, click Start
  1. Open the drop-down list by clicking on
  1. Click on animals from technology
  1. Set the day and time for which the quantities of milk are to be taken over
  1. To take over the milk quantities, start click
  1. After the takeover, the result is presented in the form of tabs and can be viewed and controlled by clicking on the respective tab.

Note: the cursor is in the tab without milk (number of animals). In these animals, there is no amount of milk on milk day, which may have to be supplemented manually if necessary.

  1. To record the missing quantities of milk, click Save, the entire list of transferred milk quantities is displayed
  1. Complement the missing milk quantities
  2. To check the completeness, continue as 4.
  1. When all milk quantities are fully recorded, click Exit MRec
  1. After a final check for completeness, the MRec is stored in messages window on the startpage and can be sent

| Add animal again (without function)

| Opens the menu item animals from technology for the transfer of milk quantities from a coupling

3. Capture the MRec with settings – tether

Note: If at Settings > farm data > farm > milk Or Settings > constants > milk > germany If tethered housing setting has been selected for the type of MRec, it should be noted that all animals with a status (Dry, Colostrum) are displayed when Capture animal the milk quantities (by default).

If only the milking animals are to be displayed, then continue with 1.

  1. Öffne Erfassung > MLP > Erfassung MLP
    • after clicking on start under MRec status all animals with a Stauss (Dry, Colostrum) are displayed
  1. Open Drop-Down List MRec-Status
  1. Setze bei M (Melkend)
    • all animals that do not have the Status Milking are hidden, the amount of milk can now be recorded manually
  2. Stop manually capture milk quantities with storage

| Add line

| Delete line

| Confirm

| Cancel | only with active line that is not yet plausible

| copy entry of all remaining animals

| Search for animal

| Info animal

Utilization | Opens context menu capture

  • Movement
  • Fertility
  • Further (…)
  • Technology
  • Add to the work list

| Settings | Opens context menu settings

  • User-defined characteristics
  • Animal identifcation
  • Edit print list

| Set display | Columns can be added individually, sequence can be changed with drag’n’drop, then save, possibly under a separate (new) name

| Filters | all animals are listed, if you remove the check mark in front of the animal, it is still displayed, by clicking on the filter becomes active, animals without check marks are hidden

| Name of the current display (displayed columns and their order), as many ads can be saved as you like

| Save display under current name / Save display as / Delete display